From d43550c14a1c6829c63c2ac0654a485f78418d6b Mon Sep 17 00:00:00 2001 From: Valera Date: Tue, 8 Mar 2016 17:52:55 +0300 Subject: [PATCH] Fix wifi issue. --- proprietary/etc/wifi/WCNSS_qcom_cfg.ini | 528 +++++++----------------- 1 file changed, 151 insertions(+), 377 deletions(-) diff --git a/proprietary/etc/wifi/WCNSS_qcom_cfg.ini b/proprietary/etc/wifi/WCNSS_qcom_cfg.ini index 4a404c1..7301624 100755 --- a/proprietary/etc/wifi/WCNSS_qcom_cfg.ini +++ b/proprietary/etc/wifi/WCNSS_qcom_cfg.ini @@ -1,377 +1,151 @@ -# This file allows user to override the factory - -# defaults for the WLAN Driver - - -# Enable IMPS or not -gEnableImps=1 - -# Enable/Disable Idle Scan - -gEnableIdleScan=0 - - -# Increase sleep duration (seconds) during IMPS -# 0 implies no periodic wake up from IMPS. Periodic wakeup is -# unnecessary if Idle Scan is disabled. -gImpsModSleepTime=0 - - -# Enable BMPS or not -gEnableBmps=1 - -# Enable suspend or not - -# 1: Enable standby, 2: Enable Deep sleep, 3: Enable Mcast/Bcast Filter - -gEnableSuspend=3 - - -# Phy Mode (auto, b, g, n, etc) -# Valid values are 0-9, with 0 = Auto, 4 = 11n, 9 = 11ac -gDot11Mode=0 - - -# CSR Roaming Enable(1) Disable(0) - -gRoamingTime=0 - - -# Assigned MAC Addresses - This will be used until NV items are in place - -# Each byte of MAC address is represented in Hex format as XX - -Intf0MacAddress=000AF58989FF -Intf1MacAddress=000AF58989FE -Intf2MacAddress=000AF58989FD - -Intf3MacAddress=000AF58989FC - - -# UAPSD service interval for VO,VI, BE, BK traffic - -InfraUapsdVoSrvIntv=0 - -InfraUapsdViSrvIntv=0 - -InfraUapsdBeSrvIntv=0 - -InfraUapsdBkSrvIntv=0 - -# Flag to allow STA send AddTspec even when ACM is Off -gAddTSWhenACMIsOff=1 - -# Make 1x1 the default antenna configuration - -gNumRxAnt=1 - - -# Beacon filtering frequency (unit in beacon intervals) - -gNthBeaconFilter=50 - - -# Enable WAPI or not - -# WAPIIsEnabled=0 - - -# Flags to filter Mcast abd Bcast RX packets. - -# Value 0: No filtering, 1: Filter all Multicast. - -# 2: Filter all Broadcast. 3: Filter all Mcast abd Bcast - -McastBcastFilter=3 - - -#Flag to enable HostARPOffload feature or not - -hostArpOffload=1 - - -#SoftAP Related Parameters - -# AP MAc addr - -gAPMacAddr=000AF589dcab - - -# 802.11n Protection flag - -gEnableApProt=1 - - -#Enable OBSS protection - -gEnableApOBSSProt=1 - - -#Enable/Disable UAPSD for SoftAP - -gEnableApUapsd=1 - - -# Fixed Rate - -gFixedRate=0 - - -# Maximum Tx power - -# gTxPowerCap=30 - - -# Fragmentation Threshold - -# gFragmentationThreshold=2346 - - -# RTS threshold - -RTSThreshold=2347 - - -# Intra-BSS forward - -gDisableIntraBssFwd=0 - - -# WMM Enable/Disable - -WmmIsEnabled=0 - - -# 802.11d support - -g11dSupportEnabled=1 - -# CCX Support and fast transition -CcxEnabled=0 -FastTransitionEnabled=1 -ImplicitQosIsEnabled=0 -gNeighborScanTimerPeriod=200 - -gNeighborScanChannelMinTime=20 -gNeighborScanChannelMaxTime=30 - -# Legacy (non-CCX, non-802.11r) Fast Roaming Support -# To enable, set FastRoamEnabled=1 -# To disable, set FastRoamEnabled=0 -FastRoamEnabled=1 - -#Check if the AP to which we are roaming is better than current AP in terms of RSSI. -#Checking is disabled if set to Zero.Otherwise it will use this value as to how better -#the RSSI of the new/roamable AP should be for roaming -RoamRssiDiff=5 - -# SAP Country code - -# Default Country Code is 2 bytes, 3rd byte is optional indoor or out door. - -# Example - -# US Indoor, USI - -# Korea Outdoor, KRO - -# Japan without optional byte, JP - -# France without optional byte, FR - -#gAPCntryCode=USI - - -#Short Guard Interval Enable/disable - -gShortGI20Mhz=1 - -gShortGI40Mhz=1 - - -#Auto Shutdown Value in seconds. A value of 0 means Auto shutoff is disabled - -gAPAutoShutOff=0 - - -# SAP auto channel selection configuration - -# 0 = disable auto channel selection - -# 1 = enable auto channel selection, channel provided by supplicant will be ignored - -gApAutoChannelSelection=1 - - -# Listen Energy Detect Mode Configuration - -# Valid values 0-128 - -# 128 means disable Energy Detect feature - -# 0-9 are threshold code and 7 is recommended value from system if feature is to be enabled. - -# 10-128 are reserved. - -# The EDET threshold mapping is as follows in 3dB step: - -# 0 = -60 dBm - -# 1 = -63 dBm - -# 2 = -66 dBm - -# ... - -# 7 = -81 dBm - -# 8 = -84 dBm - -# 9 = -87 dBm - -# Note: Any of these settings are valid. Setting 0 would yield the highest power saving (in a noisy environment) at the cost of more range. The range impact is approximately #calculated as: - -# - -# Range Loss (dB) = EDET threshold level (dBm) + 97 dBm. - -# - -gEnablePhyAgcListenMode=128 - - -#Preferred channel to start BT AMP AP mode (0 means, any channel) - -BtAmpPreferredChannel=0 - - -#Preferred band (both or 2.4 only or 5 only) - -BandCapability=0 - - -#Beacon Early Termination (1 = enable the BET feature, 0 = disable) - -enableBeaconEarlyTermination=1 - -beaconEarlyTerminationWakeInterval=11 - - -#Bluetooth Alternate Mac Phy (1 = enable the BT AMP feature, 0 = disable) - -gEnableBtAmp=0 - - -#SOFTAP Channel Range selection - -gAPChannelSelectStartChannel=1 - -gAPChannelSelectEndChannel=11 - - -#SOFTAP Channel Range selection Operating band - -# 0:2.4GHZ 1: LOW-5GHZ 2:MID-5GHZ 3:HIGH-5GHZ 4: 4.9HZ BAND - -gAPChannelSelectOperatingBand=0 - - -#Channel Bonding -gChannelBondingMode5GHz=1 - - -#Enable Keep alive with non-zero period value - -gStaKeepAlivePeriod=30 - - -#Say gGoKeepAlivePeriod(5 seconds) and gGoLinkMonitorPeriod(10 seconds). -#For every 10 seconds DUT sends Qos Null frame(i.e., Keep Alive frame if link is idle for last 10 seconds.) -#For both active and power save clients. - -#Power save clients: DUT set TIM bit from 10th second onwards and till client honors TIM bit. -#If doesn't honor for 5 seconds then Driver remove client. - -#Active clients: DUT send Qos Null frame for 10th seconds onwards if it is not success still DUT try on -#11th second if not tries on 12th and so on till 15th second. Hence before disconnection DUT will send 5 NULL frames. -#Hence in any case DUT will detect client got removed in (10+5) seconds. i.e., (gGoKeepAlivePeriod +gGoLinkMonitorPeriod).. - -#gGoLinkMonitorPeriod/ gApLinkMonitorPeriod is period where link is idle and it is period -#where we send NULL frame. - -#gApLinkMonitorPeriod = 10 - -#gGoLinkMonitorPeriod = 10 - -#gGoKeepAlivePeriod/gApKeepAlivePeriod is time to spend to check whether frame are succeed to send or not. -#Hence total effective detection time is gGoLinkMonitorPeriod+ gGoKeepAlivePeriod/gApLinkMonitorPeriod+ gApKeepAlivePeriod. - -gGoKeepAlivePeriod = 30 - -gApKeepAlivePeriod = 10 - -#If set will start with active scan after driver load, otherwise will start with - -#passive scan to find out the domain - -#gEnableBypass11d=1 - - -#If set to 0, will not scan DFS channels - -gEnableDFSChnlScan=1 - - -gVhtChannelWidth=2 -gEnableLogp=1 - - -# Enable Automatic Tx Power control - -gEnableAutomaticTxPowerControl=1 - -# 0 for OLPC 1 for CLPC and SCPC -gEnableCloseLoop=1 - -#Data Inactivity Timeout when in powersave (in ms) -gDataInactivityTimeout=200 - -# VHT Tx/Rx MCS values -# Valid values are 0,1,2. If commented out, the default value is 0. -# 0=MCS0-7, 1=MCS0-8, 2=MCS0-9 -gVhtRxMCS=2 -gVhtTxMCS=2 - -gEnableLpwrImgTransition=1 - -# Enable Tx beamforming -gTxBFEnable=1 - -# Enable Tx LDPC -#gTxLdpcEnable = 1 for HT mode, 2 for VHT mode,3 for both HT and VHT -gTxLdpcEnable=3 - -#FlexConnect Power Factor -#Default is set to 0 (disable) -gFlexConnectPowerFactor=0 - -# Valid values are 2048,4096,8192 and so on -# Please don't use values other than the ones mentioned above -gMaxMediumTime=4096 - -# 802.11K support -gRrmEnable=1 -gRrmOperChanMax=8 -gRrmNonOperChanMax=8 -gRrmRandIntvl=100 - -#Enable/Disable Modulated DTIM feature -gEnableModulatedDTIM=3 - -#max LI value for modulated DTIM -gMaxLIModulatedDTIM=3 - -END - -# Note: Configuration parser would not read anything past the END marker - +# This file allows user to override the factory +# defaults for the WLAN Driver +# Enable IMPS or not +gEnableImps=1 +# Enable/Disable Idle Scan +gEnableIdleScan=0 +# Increase sleep duration (seconds) during IMPS +# 0 implies no periodic wake up from IMPS. Periodic wakeup is +# unnecessary if Idle Scan is disabled. +gImpsModSleepTime=0 +# Enable BMPS or not +gEnableBmps=1 +# Enable Close Loop or not +gEnableCloseLoop=1 +# Enable suspend or not +# 1: Enable standby, 2: Enable Deep sleep, 3: Enable Mcast/Bcast Filter +gEnableSuspend=3 +# Phy Mode (auto, b, g, n, etc) +gDot11Mode=0 +# Handoff Enable(1) Disable(0) +gEnableHandoff=0 +# CSR Roaming Enable(1) Disable(0) +gRoamingTime=0 +# Assigned MAC Addresses - This will be used until NV items are in place +# Each byte of MAC address is represented in Hex format as XX +Intf0MacAddress=000AF58989FF +Intf1MacAddress=000AF58989FE +Intf2MacAddress=000AF58989FD +Intf3MacAddress=000AF58989FC +# UAPSD service interval for VO,VI, BE, BK traffic +InfraUapsdVoSrvIntv=0 +InfraUapsdViSrvIntv=0 +InfraUapsdBeSrvIntv=0 +InfraUapsdBkSrvIntv=0 +# Disable RSSI FW filtering +gEnableFWRssiMonitoring=0 +# Make 1x1 the default antenna configuration +gNumRxAnt=1 +# Beacon filtering frequency (unit in beacon intervals) +gNthBeaconFilter=50 +# Enable WAPI or not +# WAPIIsEnabled=0 +# Flags to filter Mcast abd Bcast RX packets. +# Value 0: No filtering, 1: Filter all Multicast. +# 2: Filter all Broadcast. 3: Filter all Mcast abd Bcast +McastBcastFilter=3 +#Flag to enable HostARPOffload feature or not +hostArpOffload=0 +#SoftAP Related Parameters +# AP MAc addr +gAPMacAddr=000AF58989EF +# 802.11n Protection flag +gEnableApProt=1 +#Enable OBSS protection +gEnableApOBSSProt=0 +#Enable/Disable UAPSD for SoftAP +gEnableApUapsd=1 +# Fixed Rate +gFixedRate=0 +# Maximum Tx power +# gTxPowerCap=30 +# Fragmentation Threshold +# gFragmentationThreshold=2346 +# RTS threshold +RTSThreshold=2347 +# Intra-BSS forward +gDisableIntraBssFwd=0 +# WMM Enable/Disable +WmmIsEnabled=0 +# 802.11d support +g11dSupportEnabled=1 +# CCX Support and fast transition +CcxEnabled=0 +FastTransitionEnabled=0 +ImplicitQosIsEnabled=1 +gNeighborScanTimerPeriod=200 +gNeighborLookupThreshold=50 +gNeighborReassocThreshold=55 +gNeighborScanChannelList=1,11,36,64 +gNeighborScanChannelMinTime=20 +gNeighborScanChannelMaxTime=30 +gMaxNeighborReqTries=3 +# SAP Country code +# Default Country Code is 2 bytes, 3rd byte is optional indoor or out door. +# Example +# US Indoor, USI +# Korea Outdoor, KRO +# Japan without optional byte, JP +# France without optional byte, FR +#gAPCntryCode=USI +#Short Guard Interval Enable/disable +gShortGI20Mhz=1 +gShortGI40Mhz=1 +#Auto Shutdown Value in seconds. A value of 0 means Auto shutoff is disabled +gAPAutoShutOff=0 +# SAP auto channel selection configuration +# 0 = disable auto channel selection +# 1 = enable auto channel selection, channel provided by supplicant will be ignored +gApAutoChannelSelection=0 +# Listen Energy Detect Mode Configuration +# Valid values 0-128 +# 128 means disable Energy Detect feature +# 0-9 are threshold code and 7 is recommended value from system if feature is to be enabled. +# 10-128 are reserved. +# The EDET threshold mapping is as follows in 3dB step: +# 0 = -60 dBm +# 1 = -63 dBm +# 2 = -66 dBm +# ... +# 7 = -81 dBm +# 8 = -84 dBm +# 9 = -87 dBm +# Note: Any of these settings are valid. Setting 0 would yield the highest power saving (in a noisy environment) at the cost of more range. The range impact is approximately #calculated as: +# +# Range Loss (dB) = EDET threshold level (dBm) + 97 dBm. +# +gEnablePhyAgcListenMode=128 +#Preferred band (both or 2.4 only or 5 only) +BandCapability=0 +#Forced Device Listen Interval in multiples of DTIM Period aligned to DTIM +gEnableModulatedDTIM=3 +#Beacon Early Termination (1 = enable the BET feature, 0 = disable) +enableBeaconEarlyTermination=1 +beaconEarlyTerminationWakeInterval=11 +#Bluetooth Alternate Mac Phy (1 = enable the BT AMP feature, 0 = disable) +gEnableBtAmp=0 +#Preferred channel to start BT AMP AP mode (0 means, any channel) +BtAmpPreferredChannel=0 +#SOFTAP Channel Range selection +gAPChannelSelectStartChannel=1 +gAPChannelSelectEndChannel=11 +#SOFTAP Channel Range selection Operating band +# 0:2.4GHZ 1: LOW-5GHZ 2:MID-5GHZ 3:HIGH-5GHZ 4: 4.9HZ BAND +gAPChannelSelectOperatingBand=0 +#Enable Keep alive with non-zero period value +gStaKeepAlivePeriod = 25 +#If set will start with active scan after driver load, otherwise will start with +#passive scan to find out the domain +gEnableBypass11d=1 +#If set to 0, will not scan DFS channels +gEnableDFSChnlScan=0 +# Enable logp/SSR +gEnableLogp=1 +# Disable HT40 +gChannelBondingMode5GHz=0 +# Enable Automatic Tx Power control +gEnableAutomaticTxPowerControl=1 +# Derive P2P MAC address from primary MAC address +isP2pDeviceAddrAdministrated=1 +END +# Note: Configuration parser would not read anything past the END marker \ No newline at end of file