401 lines
7.3 KiB
INI
401 lines
7.3 KiB
INI
# This file allows user to override the factory
|
|
|
|
# defaults for the WLAN Driver
|
|
|
|
|
|
# Enable IMPS or not
|
|
gEnableImps=1
|
|
|
|
# Enable/Disable Idle Scan
|
|
|
|
gEnableIdleScan=0
|
|
|
|
|
|
# Increase sleep duration (seconds) during IMPS
|
|
# 0 implies no periodic wake up from IMPS. Periodic wakeup is
|
|
# unnecessary if Idle Scan is disabled.
|
|
gImpsModSleepTime=0
|
|
|
|
|
|
# Enable BMPS or not
|
|
gEnableBmps=1
|
|
|
|
# Enable suspend or not
|
|
|
|
# 1: Enable standby, 2: Enable Deep sleep, 3: Enable Mcast/Bcast Filter
|
|
|
|
gEnableSuspend=3
|
|
|
|
|
|
# Phy Mode (auto, b, g, n, etc)
|
|
# Valid values are 0-9, with 0 = Auto, 4 = 11n, 9 = 11ac
|
|
gDot11Mode=0
|
|
|
|
|
|
# CSR Roaming Enable(1) Disable(0)
|
|
|
|
gRoamingTime=0
|
|
|
|
|
|
# Assigned MAC Addresses - This will be used until NV items are in place
|
|
|
|
# Each byte of MAC address is represented in Hex format as XX
|
|
|
|
Intf0MacAddress=000AF58989FF
|
|
Intf1MacAddress=000AF58989FE
|
|
Intf2MacAddress=000AF58989FD
|
|
|
|
Intf3MacAddress=000AF58989FC
|
|
|
|
|
|
# UAPSD service interval for VO,VI, BE, BK traffic
|
|
|
|
InfraUapsdVoSrvIntv=0
|
|
|
|
InfraUapsdViSrvIntv=0
|
|
|
|
InfraUapsdBeSrvIntv=0
|
|
|
|
InfraUapsdBkSrvIntv=0
|
|
|
|
|
|
# Make 1x1 the default antenna configuration
|
|
|
|
gNumRxAnt=1
|
|
|
|
|
|
# Beacon filtering frequency (unit in beacon intervals)
|
|
|
|
gNthBeaconFilter=50
|
|
|
|
|
|
# Enable WAPI or not
|
|
|
|
# WAPIIsEnabled=0
|
|
|
|
|
|
# Flags to filter Mcast abd Bcast RX packets.
|
|
|
|
# Value 0: No filtering, 1: Filter all Multicast.
|
|
|
|
# 2: Filter all Broadcast. 3: Filter all Mcast abd Bcast
|
|
|
|
McastBcastFilter=2
|
|
|
|
|
|
#Flag to enable HostARPOffload feature or not
|
|
|
|
hostArpOffload=1
|
|
|
|
|
|
#SoftAP Related Parameters
|
|
|
|
# AP MAc addr
|
|
|
|
gAPMacAddr=000AF589dcab
|
|
|
|
|
|
# 802.11n Protection flag
|
|
|
|
gEnableApProt=1
|
|
|
|
|
|
#Enable OBSS protection
|
|
|
|
gEnableApOBSSProt=0
|
|
|
|
|
|
#Enable/Disable UAPSD for SoftAP
|
|
|
|
gEnableApUapsd=0
|
|
|
|
|
|
# Fixed Rate
|
|
|
|
gFixedRate=0
|
|
|
|
|
|
# Maximum Tx power
|
|
|
|
# gTxPowerCap=30
|
|
|
|
|
|
# Fragmentation Threshold
|
|
|
|
# gFragmentationThreshold=2346
|
|
|
|
|
|
# RTS threshold
|
|
|
|
RTSThreshold=2347
|
|
|
|
|
|
# Intra-BSS forward
|
|
|
|
gDisableIntraBssFwd=0
|
|
|
|
|
|
# WMM Enable/Disable
|
|
|
|
WmmIsEnabled=0
|
|
|
|
|
|
# 802.11d support
|
|
|
|
g11dSupportEnabled=0
|
|
|
|
# CCX Support and fast transition
|
|
CcxEnabled=1
|
|
FastTransitionEnabled=1
|
|
ImplicitQosIsEnabled=1
|
|
gNeighborScanTimerPeriod=200
|
|
|
|
gNeighborLookupThreshold=78
|
|
|
|
gNeighborScanChannelMinTime=20
|
|
gNeighborScanChannelMaxTime=30
|
|
|
|
# Legacy (non-CCX, non-802.11r) Fast Roaming Support
|
|
# To enable, set FastRoamEnabled=1
|
|
# To disable, set FastRoamEnabled=0
|
|
FastRoamEnabled=1
|
|
|
|
#Check if the AP to which we are roaming is better than current AP in terms of RSSI.
|
|
#Checking is disabled if set to Zero.Otherwise it will use this value as to how better
|
|
#the RSSI of the new/roamable AP should be for roaming
|
|
RoamRssiDiff=5
|
|
|
|
# SAP Country code
|
|
|
|
# Default Country Code is 2 bytes, 3rd byte is optional indoor or out door.
|
|
|
|
# Example
|
|
|
|
# US Indoor, USI
|
|
|
|
# Korea Outdoor, KRO
|
|
|
|
# Japan without optional byte, JP
|
|
|
|
# France without optional byte, FR
|
|
|
|
#gAPCntryCode=USI
|
|
|
|
|
|
#Short Guard Interval Enable/disable
|
|
|
|
gShortGI20Mhz=1
|
|
|
|
gShortGI40Mhz=1
|
|
|
|
|
|
#Auto Shutdown Value in seconds. A value of 0 means Auto shutoff is disabled
|
|
|
|
gAPAutoShutOff=0
|
|
|
|
|
|
# SAP auto channel selection configuration
|
|
|
|
# 0 = disable auto channel selection
|
|
|
|
# 1 = enable auto channel selection, channel provided by supplicant will be ignored
|
|
|
|
gApAutoChannelSelection=0
|
|
|
|
|
|
# Listen Energy Detect Mode Configuration
|
|
|
|
# Valid values 0-128
|
|
|
|
# 128 means disable Energy Detect feature
|
|
|
|
# 0-9 are threshold code and 7 is recommended value from system if feature is to be enabled.
|
|
|
|
# 10-128 are reserved.
|
|
|
|
# The EDET threshold mapping is as follows in 3dB step:
|
|
|
|
# 0 = -60 dBm
|
|
|
|
# 1 = -63 dBm
|
|
|
|
# 2 = -66 dBm
|
|
|
|
# ...
|
|
|
|
# 7 = -81 dBm
|
|
|
|
# 8 = -84 dBm
|
|
|
|
# 9 = -87 dBm
|
|
|
|
# Note: Any of these settings are valid. Setting 0 would yield the highest power saving (in a noisy environment) at the cost of more range. The range impact is approximately #calculated as:
|
|
|
|
#
|
|
|
|
# Range Loss (dB) = EDET threshold level (dBm) + 97 dBm.
|
|
|
|
#
|
|
|
|
gEnablePhyAgcListenMode=128
|
|
|
|
|
|
#Preferred channel to start BT AMP AP mode (0 means, any channel)
|
|
|
|
BtAmpPreferredChannel=0
|
|
|
|
|
|
#Preferred band (both or 2.4 only or 5 only)
|
|
|
|
BandCapability=0
|
|
|
|
|
|
#Beacon Early Termination (1 = enable the BET feature, 0 = disable)
|
|
|
|
enableBeaconEarlyTermination=1
|
|
|
|
beaconEarlyTerminationWakeInterval=11
|
|
|
|
|
|
#Bluetooth Alternate Mac Phy (1 = enable the BT AMP feature, 0 = disable)
|
|
|
|
gEnableBtAmp=0
|
|
|
|
|
|
#SOFTAP Channel Range selection
|
|
|
|
gAPChannelSelectStartChannel=1
|
|
|
|
gAPChannelSelectEndChannel=11
|
|
|
|
|
|
#SOFTAP Channel Range selection Operating band
|
|
|
|
# 0:2.4GHZ 1: LOW-5GHZ 2:MID-5GHZ 3:HIGH-5GHZ 4: 4.9HZ BAND
|
|
|
|
gAPChannelSelectOperatingBand=0
|
|
|
|
|
|
#Channel Bonding
|
|
gChannelBondingMode5GHz=1
|
|
|
|
|
|
#Enable Keep alive with non-zero period value
|
|
|
|
gStaKeepAlivePeriod=30
|
|
|
|
|
|
#Say gGoKeepAlivePeriod(5 seconds) and gGoLinkMonitorPeriod(10 seconds).
|
|
#For every 10 seconds DUT send Qos Null frame(i.e., Keep Alive frame if link is idle for last 10 seconds.)
|
|
#For both active and power save clients.
|
|
|
|
#Power save clients: DUT set TIM bit from 10th second onwards and till client honors TIM bit.
|
|
#If doesn't honor for 5 seconds then DUT remove client.
|
|
|
|
#Active clients: DUT send Qos Null frame for 10th seconds onwards if it is not success still we try on
|
|
#11th second if not tries on 12th and so on till 15th second. Hence before disconnection DUT will send 5 NULL frames.
|
|
#Hence in any case DUT will detect client got removed in (10+5) seconds. i.e., (gGoKeepAlivePeriod + gGoLinkMonitorPeriod)..
|
|
|
|
#gGoLinkMonitorPeriod/gApLinkMonitorPeriod is period where link is idle and it is period
|
|
#where we send NULL frame.
|
|
|
|
gApLinkMonitorPeriod=30
|
|
|
|
gGoLinkMonitorPeriod=10
|
|
|
|
#gGoKeepAlivePeriod/gApKeepAlivePeriod is time to spend to check whether frame are succeed to send or not.
|
|
#Hence total effective detection time is gGoLinkMonitorPeriod + gGoKeepAlivePeriod/gApLinkMonitorPeriod+ gApKeepAlivePeriod.
|
|
|
|
gGoKeepAlivePeriod=3
|
|
|
|
gApKeepAlivePeriod=10
|
|
|
|
|
|
#If set will start with active scan after driver load, otherwise will start with
|
|
|
|
#passive scan to find out the domain
|
|
|
|
gEnableBypass11d=1
|
|
|
|
|
|
#If set to 0, will not scan DFS channels
|
|
|
|
gEnableDFSChnlScan=1
|
|
|
|
|
|
gVhtChannelWidth=2
|
|
gEnableLogp=1
|
|
|
|
|
|
# Enable Automatic Tx Power control
|
|
|
|
gEnableAutomaticTxPowerControl=0
|
|
|
|
# 0 for OLPC 1 for CLPC and SCPC
|
|
gEnableCloseLoop=1
|
|
|
|
#Data Inactivity Timeout when in powersave (in ms)
|
|
gDataInactivityTimeout=200
|
|
|
|
# VHT Tx/Rx MCS values
|
|
# Valid values are 0,1,2. If commented out, the default value is 0.
|
|
# 0=MCS0-7, 1=MCS0-8, 2=MCS0-9
|
|
gVhtRxMCS=2
|
|
gVhtTxMCS=2
|
|
|
|
gEnableLpwrImgTransition=1
|
|
|
|
# Enable Tx beamforming
|
|
gTxBFEnable=1
|
|
|
|
# Enable Tx LDPC
|
|
#gTxLdpcEnable = 1 for HT mode, 2 for VHT mode,3 for both HT and VHT
|
|
gTxLdpcEnable=3
|
|
|
|
# Oxygen network (prop IE for IBSS)
|
|
gEnableOxygenNwk=0
|
|
|
|
#FlexConnect Power Factor
|
|
#Default is set to 0 (disable)
|
|
gFlexConnectPowerFactor=0
|
|
|
|
# Valid values are 2048,4096,8192 and so on
|
|
# Please don't use values other than the ones mentioned above
|
|
gMaxMediumTime=4096
|
|
|
|
# Enable P2P administrated interface
|
|
isP2pDeviceAddrAdministrated=1
|
|
|
|
# To Skip DFS Channel in P2P Search
|
|
gSkipDfsChannelInP2pSearch=1
|
|
|
|
# Enable/Disable Mcast addr list filtering
|
|
# isMcAddrListFilter deprecated
|
|
gMCAddrListEnable=1
|
|
|
|
# TDLS setting
|
|
gEnableTDLSSupport=1
|
|
gEnableTDLSImplicitTrigger=1
|
|
gEnableTDLSBufferSta=0
|
|
gTDLSMaxDiscoveryAttempt=5
|
|
gTDLSIdleTimeout=10000
|
|
|
|
# Country code priority
|
|
gCountryCodePriority=1
|
|
|
|
gReportMaxLinkSpeed=2
|
|
|
|
#PNO scan enable = 1 / disable =0
|
|
gPNOScanSupport=0
|
|
|
|
# Modulated DTIM =3
|
|
gEnableModulatedDTIM=3
|
|
|
|
# Connect more than 8 devices with Wi-Fi Direct
|
|
gEnableVSTASupport=1
|
|
|
|
END
|
|
|
|
# Note: Configuration parser would not read anything past the END marker
|
|
|