rollback wifi driver

wifi/WCNSS_qcom_cfg.ini

@@ -11,10 +11,6 @@ gEnableImps=1
 gEnableIdleScan=0
 
 
-# Enable/Disable vsta based on MAX Assoc limit
-gEnableVSTASupport=1
-
-
 # Increase sleep duration (seconds) during IMPS
 # 0 implies no periodic wake up from IMPS. Periodic wakeup is 
 # unnecessary if Idle Scan is disabled.
@@ -30,6 +26,7 @@ gEnableBmps=1
 
 gEnableSuspend=3
 
+
 # Phy Mode (auto, b, g, n, etc)
 # Valid values are 0-9, with 0 = Auto, 4 = 11n, 9 = 11ac
 gDot11Mode=0
@@ -61,8 +58,6 @@ InfraUapsdBeSrvIntv=0
 
 InfraUapsdBkSrvIntv=0
 
-# Flag to allow STA send AddTspec even when ACM is Off
-gAddTSWhenACMIsOff=1
 
 # Make 1x1 the default antenna configuration
 
@@ -116,7 +111,7 @@ gEnableApOBSSProt=1
 
 #Enable/Disable UAPSD for SoftAP
 
-gEnableApUapsd=1
+gEnableApUapsd=0
 
 
 # Fixed Rate
@@ -157,9 +152,10 @@ g11dSupportEnabled=1
 
 g11hSupportEnabled=1
 
-# ESE Support and fast transition
-EseEnabled=0
-ImplicitQosIsEnabled=0
+# CCX Support and fast transition
+CcxEnabled=0
+FastTransitionEnabled=1
+ImplicitQosIsEnabled=1
 gNeighborScanTimerPeriod=200
 
 gNeighborLookupThreshold=76
@@ -169,7 +165,7 @@ gNeighborScanChannelMinTime=20
 gNeighborScanChannelMaxTime=30
 gMaxNeighborReqTries=3
 
-# Legacy (non-ESE, non-802.11r) Fast Roaming Support
+# Legacy (non-CCX, non-802.11r) Fast Roaming Support
 # To enable, set FastRoamEnabled=1
 # To disable, set FastRoamEnabled=0
 FastRoamEnabled=1
@@ -187,10 +183,9 @@ gImmediateRoamRssiDiff=10
 
 # To enable, set gRoamIntraBand=1 (Roaming within band)
 # To disable, set gRoamIntraBand=0 (Roaming across band)
-
 gRoamIntraBand=0
 
-#SAP Country code
+# SAP Country code
 
 # Default Country Code is 2 bytes, 3rd byte is optional indoor or out door.
 
@@ -225,7 +220,7 @@ gAPAutoShutOff=0
 
 # 1 = enable auto channel selection, channel provided by supplicant will be ignored
 
-gApAutoChannelSelection=1
+gApAutoChannelSelection=0
 
 
 # Listen Energy Detect Mode Configuration
@@ -277,7 +272,7 @@ BandCapability=0
 
 #Beacon Early Termination (1 = enable the BET feature, 0 = disable)
 
-enableBeaconEarlyTermination=0
+enableBeaconEarlyTermination=1
 
 beaconEarlyTerminationWakeInterval=3
 
@@ -303,37 +298,18 @@ gAPChannelSelectOperatingBand=0
 
 #Channel Bonding
 gChannelBondingMode5GHz=1
-gChannelBondingMode24GHz=1
+
 
 #Enable Keep alive with non-zero period value
 
-#gStaKeepAlivePeriod = 30
+gStaKeepAlivePeriod = 30
 
-#Say gGoKeepAlivePeriod(5 seconds) and gGoLinkMonitorPeriod(10 seconds).
-#For every 10 seconds DUT send Qos Null frame(i.e., Keep Alive frame if link is idle for last 10 seconds.)
-#For both active and power save clients.
+#AP LINK MONITOR TIMEOUT is used for both SAP and GO mode.
+#It is used to change the frequency of keep alive packets in the AP Link Monitor period which is by
+#default 20s. Currently the keep alive packets are sent as an interval of 3s but after this change
+#the keep alive packet frequency can be changed.
 
-#Power save clients: DUT set TIM bit from 10th second onwards and till client honors TIM bit.
-#If doesn't honor for 5 seconds then DUT remove client.
-
-#Active clients: DUT send Qos Null frame for 10th seconds onwards if it is not success still we try on
-#11th second if not tries on 12th and so on till 15th second. Hence before disconnection DUT will send 5 NULL frames.
-#Hence in any case DUT will detect client got removed in (10+5) seconds. i.e., (gGoKeepAlivePeriod + gGoLinkMonitorPeriod)..
-
-#gGoLinkMonitorPeriod/ gApLinkMonitorPeriod is period where link is idle and it is period
-#where we send NULL frame.
-
-#gApLinkMonitorPeriod = 10
-
-#gGoLinkMonitorPeriod = 10
-
-#gGoKeepAlivePeriod/gApKeepAlivePeriod is time to spend to check whether frame are succeed to send or not.
-#Hence total effective detection time is gGoLinkMonitorPeriod+ gGoKeepAlivePeriod/gApLinkMonitorPeriod+ gApKeepAlivePeriod.
-
-
-gGoKeepAlivePeriod=30
-
-gApKeepAlivePeriod=10
+#gApLinkMonitorPeriod = 3
 
 
 #If set will start with active scan after driver load, otherwise will start with
@@ -354,7 +330,7 @@ gEnableLogp=1
 
 # Enable Automatic Tx Power control
 
-gEnableAutomaticTxPowerControl=0
+gEnableAutomaticTxPowerControl=1
 
 # 0 for OLPC 1 for CLPC and SCPC
 gEnableCloseLoop=1
@@ -409,7 +385,7 @@ gEnableFastRoamInConcurrency=1
 gListOfNon11acCountryCode=RU,UA,ZA
 
 #Maxium Channel time in msec
-gMaxMediumTime = 5480
+gMaxMediumTime = 6000
 
 # 802.11K support
 gRrmEnable=1
@@ -420,6 +396,9 @@ gRrmRandIntvl=100
 #Scan offload
 gEnableDirectedScanOffload=0
 
+# Oxygen network (prop IE for IBSS)
+gEnableOxygenNwk=0
+
 #FlexConnect Power Factor
 #Default is set to 0 (disable)
 gFlexConnectPowerFactor=0
@@ -428,22 +407,6 @@ gFlexConnectPowerFactor=0
 gEnableTrafficMonitor=1
 gTrafficIdleTimeout=3000
 
-#Disable/Enable Strict FCC Regulatory
-# 0 to disable, 1 to enable
-gEnableStrictRegulatoryForFCC=1
-
-#Enable/Disable Modulated DTIM feature
-gEnableModulatedDTIM=3
-
-#max LI value for modulated DTIM
-gMaxLIModulatedDTIM=3
-
-#Enable/Disable Link Layer Statistics Feature
-gEnableLLStats=1
-
-#Enable/Disable EXTScan Feature
-gEnableEXTScan=1
-
 END
 
 # Note: Configuration parser would not read anything past the END marker