mondrianwifi: use stock wifi conf

wifi/WCNSS_qcom_cfg.ini

@@ -80,7 +80,7 @@ gNthBeaconFilter=50
 
 # 2: Filter all Broadcast. 3: Filter all Mcast abd Bcast
 
-McastBcastFilter=3
+McastBcastFilter=2
 
 
 #Flag to enable HostARPOffload feature or not
@@ -88,10 +88,6 @@ McastBcastFilter=3
 hostArpOffload=1
 
 
-#Flag to enable HostNSOffload feature or not
-
-hostNSOffload=0
-
 #SoftAP Related Parameters
 
 # AP MAc addr
@@ -106,7 +102,7 @@ gEnableApProt=1
 
 #Enable OBSS protection
 
-gEnableApOBSSProt=1
+gEnableApOBSSProt=0
 
 
 #Enable/Disable UAPSD for SoftAP
@@ -146,24 +142,18 @@ WmmIsEnabled=0
 
 # 802.11d support
 
-g11dSupportEnabled=1
+g11dSupportEnabled=0
-
-# 802.11h support
-
-g11hSupportEnabled=1
 
 # CCX Support and fast transition
-CcxEnabled=0
+CcxEnabled=1
 FastTransitionEnabled=1
 ImplicitQosIsEnabled=1
 gNeighborScanTimerPeriod=200
 
-gNeighborLookupThreshold=76
+gNeighborLookupThreshold=78
-gNeighborReassocThreshold=81
 
 gNeighborScanChannelMinTime=20
 gNeighborScanChannelMaxTime=30
-gMaxNeighborReqTries=3
 
 # Legacy (non-CCX, non-802.11r) Fast Roaming Support
 # To enable, set FastRoamEnabled=1
@@ -173,17 +163,7 @@ FastRoamEnabled=1
 #Check if the AP to which we are roaming is better than current AP in terms of RSSI.
 #Checking is disabled if set to Zero.Otherwise it will use this value as to how better
 #the RSSI of the new/roamable AP should be for roaming
-RoamRssiDiff=3
+RoamRssiDiff=5
-
-# If the RSSI of any available candidate is better than currently associated
-# AP by at least gImmediateRoamRssiDiff, then being to roam immediately (without
-# registering for reassoc threshold).
-# NOTE: Value of 0 means that we would register for reassoc threshold.
-gImmediateRoamRssiDiff=10
-
-# To enable, set gRoamIntraBand=1 (Roaming within band)
-# To disable, set gRoamIntraBand=0 (Roaming across band)
-gRoamIntraBand=0
 
 # SAP Country code
 
@@ -274,7 +254,7 @@ BandCapability=0
 
 enableBeaconEarlyTermination=1
 
-beaconEarlyTerminationWakeInterval=3
+beaconEarlyTerminationWakeInterval=11
 
 
 #Bluetooth Alternate Mac Phy (1 = enable the BT AMP feature, 0 = disable)
@@ -302,14 +282,33 @@ gChannelBondingMode5GHz=1
 
 #Enable Keep alive with non-zero period value
 
-gStaKeepAlivePeriod = 30
+gStaKeepAlivePeriod=30
 
-#AP LINK MONITOR TIMEOUT is used for both SAP and GO mode.
-#It is used to change the frequency of keep alive packets in the AP Link Monitor period which is by
-#default 20s. Currently the keep alive packets are sent as an interval of 3s but after this change
-#the keep alive packet frequency can be changed.
 
-#gApLinkMonitorPeriod = 3
+#Say gGoKeepAlivePeriod(5 seconds) and gGoLinkMonitorPeriod(10 seconds).
+#For every 10 seconds DUT send Qos Null frame(i.e., Keep Alive frame if link is idle for last 10 seconds.)
+#For both active and power save clients.
+
+#Power save clients: DUT set TIM bit from 10th second onwards and till client honors TIM bit.
+#If doesn't honor for 5 seconds then DUT remove client.
+
+#Active clients: DUT send Qos Null frame for 10th seconds onwards if it is not success still we try on
+#11th second if not tries on 12th and so on till 15th second. Hence before disconnection DUT will send 5 NULL frames.
+#Hence in any case DUT will detect client got removed in (10+5) seconds. i.e., (gGoKeepAlivePeriod + gGoLinkMonitorPeriod)..
+
+#gGoLinkMonitorPeriod/gApLinkMonitorPeriod is period where link is idle and it is period
+#where we send NULL frame.
+
+gApLinkMonitorPeriod=30
+
+gGoLinkMonitorPeriod=10
+
+#gGoKeepAlivePeriod/gApKeepAlivePeriod is time to spend to check whether frame are succeed to send or not.
+#Hence total effective detection time is gGoLinkMonitorPeriod + gGoKeepAlivePeriod/gApLinkMonitorPeriod+ gApKeepAlivePeriod.
+
+gGoKeepAlivePeriod=3
+
+gApKeepAlivePeriod=10
 
 
 #If set will start with active scan after driver load, otherwise will start with
@@ -330,7 +329,7 @@ gEnableLogp=1
 
 # Enable Automatic Tx Power control
 
-gEnableAutomaticTxPowerControl=1
+gEnableAutomaticTxPowerControl=0
 
 # 0 for OLPC 1 for CLPC and SCPC
 gEnableCloseLoop=1
@@ -344,57 +343,14 @@ gDataInactivityTimeout=200
 gVhtRxMCS=2
 gVhtTxMCS=2
 
-# Enable CRDA regulatory support by settings default country code
+gEnableLpwrImgTransition=1
-#gCrdaDefaultCountryCode=TW
 
-# Scan Timing Parameters
+# Enable Tx beamforming
-# gPassiveMaxChannelTime=110
+gTxBFEnable=1
-# gPassiveMinChannelTime=60
-# gActiveMaxChannelTime=40
-# gActiveMinChannelTime=20
 
-#If set to 0, MCC is not allowed.
+# Enable Tx LDPC
-gEnableMCCMode=1
+#gTxLdpcEnable = 1 for HT mode, 2 for VHT mode,3 for both HT and VHT
-
+gTxLdpcEnable=3
-# 1=enable STBC; 0=disable STBC 
-gEnableRXSTBC=1
-
-# Enable Active mode offload
-gEnableActiveModeOffload=1
-
-#Enable Scan Results Aging based on timer 
-#Timer value is in seconds
-#If Set to 0 it will not enable the feature
-gScanAgingTime=0
-
-#Enable Power saving mechanism Based on Android Framework
-#If set to 0 Driver internally control the Power saving mechanism
-#If set to 1 Android Framwrok control the Power saving mechanism
-isAndroidPsEn=0
-
-#disable LDPC in STA mode if the AP is TXBF capable
-gDisableLDPCWithTxbfAP=1
-
-#Enable thermal mitigation
-gThermalMitigationEnable=1
-
-gEnableFastRoamInConcurrency=1
-
-#List of Country codes for which 11ac needs to be disabled
-#Each country code must be delimited by comma(,)
-gListOfNon11acCountryCode=RU,UA,ZA
-
-#Maxium Channel time in msec
-gMaxMediumTime = 6000
-
-# 802.11K support
-gRrmEnable=1
-gRrmOperChanMax=8
-gRrmNonOperChanMax=8
-gRrmRandIntvl=100
-
-#Scan offload
-gEnableDirectedScanOffload=0
 
 # Oxygen network (prop IE for IBSS)
 gEnableOxygenNwk=0
@@ -403,9 +359,40 @@ gEnableOxygenNwk=0
 #Default is set to 0 (disable)
 gFlexConnectPowerFactor=0
 
-#SAP/P2P-GO mode traffic monitor
+# Valid values are 2048,4096,8192 and so on
-gEnableTrafficMonitor=1
+# Please don't use values other than the ones mentioned above
-gTrafficIdleTimeout=3000
+gMaxMediumTime=4096
+
+# Enable P2P administrated interface
+isP2pDeviceAddrAdministrated=1
+
+# To Skip DFS Channel in P2P Search
+gSkipDfsChannelInP2pSearch=1
+
+# Enable/Disable Mcast addr list filtering
+# isMcAddrListFilter deprecated
+gMCAddrListEnable=1
+
+# TDLS setting
+gEnableTDLSSupport=1
+gEnableTDLSImplicitTrigger=1
+gEnableTDLSBufferSta=0
+gTDLSMaxDiscoveryAttempt=5
+gTDLSIdleTimeout=10000
+
+# Country code priority
+gCountryCodePriority=1 
+
+gReportMaxLinkSpeed=2
+
+#PNO scan enable = 1 / disable =0 
+gPNOScanSupport=0
+
+# Modulated DTIM =3
+gEnableModulatedDTIM=3
+
+# Connect more than 8 devices with Wi-Fi Direct
+gEnableVSTASupport=1
 
 END